A conversion with no knowledge, but with the best of intentions.

Welcome to UKHIppy2764@2x.png

UKHippy is a long running online community and of likeminded people exploring all interpretations on what it means to be living an alternative lifestyle -- we welcome discussions on everything related to sustainability, the environment, alternative spirituality, music, festivals, politics and more -- membership of this website is free but supported by the community.

  • So it begins! We have now officially started our conversion! Will try and keep this updated and show any progress we make. But I suspect that most of my posts on here will be questions and to ask advice as I've no idea what I'm doing.


    We didn't actually get much done today, we threw a few bits out, noted what we will pull out and sell, had a quick clean and pulled up some of the rubber matting. But then the sun got it's shine on, so we decided to go for something to eat and a drink instead :). With this kind of work ethic we will be finished in no time!


    We are planning on perhaps selling the horse partitions, the oven, the hobs, the fridge and possibly the water heater (can't seem to get that working).


    The floor under the matting looks to be wooden sheets (about an inch thick) mounted on top of what looks like thicker railway sleeper style planks. As I've said before, I am really no expert and I am going into this a bit blind....but is this normal? I was expecting some kind of metal sheet under the sub floor. In terms of the state of the floor beneath the rubber matting, about a 1/4 of it needs replacing, but I wanted to replace the whole lot anyway so it doesn't matter too much. And perhaps the sleeper too, but it seemed pretty solid and uncorrupted.


    We've done a few quick layout designs and know roughly where we want things (my girlfriend wants the kitchen sink by a window so she can look out when she does the washing up....which is funny as it's usually me that does it!), but when you have that ramp down and can bring the outdoors into your space, that is something we have to incorporate somehow.


    Anyway, here are a few photos of today's small progress :).





  • No steel sub floor then?


    Well at not in the back end at least. Is this a good thing? I feel like it's a good thing as I didn't want to be pulling out loads of rusted metal. And could I put my own metal sub floor in if I wanted too?


    Is it a gas oven, and is it a combined hob sink?


    You're certainly not going to be short of room in there :D


    It's a gas oven, but we need something we can mount out of the reach of little arms (we have a 1 yr old son that is very mobile). And it's a separate hob and sink, but they are both too big for us. We only really need a small sink and 2 burners.


    Damn...that is Mahoosive!


    Sent from my MotoE2(4G-LTE) using Tapatalk


    It's just shy of 8m in length, I think each panel on the side is 1.1m. With the ramp down it seems a bazillion times bigger!


    What a fantastic project
    You can have rooms in there so when you have an argument you can slam doors and everything.


    When I have an argument and slam the door I find myself outside in a field wearing just me socks:curse:


    Paul


    The doors will most likely be sliding doors, the slam they produce just isn't very satisfying :(.

  • Quick update!


    Slowly pulling everything out and have now totally decimated what was the old living area. Removed all the cupboards, removed carpet on walls (why do people carpet walls? It is truly dreadful!), pulled out the electrics, laminate flooring gone, fridge and cooker gone. All we pretty much have in there now is half a seat, the sub floor and the plywood walls with the polystyrene insulation. This will all come out too in time, the walls are a bit rank...could stay but I'd rather not take any chances, the sink had no drainage and basically the waste water would just drop out and leave the vehicle via a hole in the sub floor...so the floor is also a bit dodgy in the front end.


    Next job is to finish any little jobs in the front, remove the partition walls and get the shower/toilet out. Then it'll be time to take on what has been my nemesis of the whole build so far, a large metal beam that was used to hold the old horse partitions in place. The thing is riveted in place from underneath with giant bolts about an inch and a half thick. I'll need some kind of laser to cut it out!


    I'll pop up some photos later to show the damage we've done :).

  • I knew there must be some kind of logical and practical reason for it, but the stuff we pulled off looked like old 90's office flooring.


    The biggest challenge to date is getting the time. We have a 1 year old son that is already one hell of a climber, fiddler and explorer....no way we could concentrate on what we are doing if he was around on site. So we are doing it in shifts and using up all the baby sitting promises we accrued through my lady's pregnancy :).


    Anyway, here is the mess we've made so far...





  • I had one of those in my box. I plugged the holes with fluff and built up the floor around it! I've got a couple of inches of floor insulation so it more than covered it. Those compressed foam sleeping mats are great for padding miscellaneous gaps


    I would leave it there if I could, but it's butted up right against the wall where the horses rear end was facing. And that wall is riveted in across the bottom. I was thinking that the floor is coming out anyway so I could cut around it and just get it out that way?

  • Hi again! Conversion is still coming along nicely and a few big steps have been made.....mainly with the help of a angle grinder and a huge crowbar.


    What I have discovered so far is that our biggest problem isn't time, money or knowledge.....it's finding a regular babysitter for our boy.


    Haven't updated in a while due to moving to a new temporary address, having a big bust up with the ex landlord (which totally re-enforces our reasons for doing this) and us both being swamped at work. We have gutted 90% of the horsebox interior, removed as much rust as we could, put a few layers of red oxide on. We've also started damp proofing, turning the horse box into a GOTH BOX!!


    While it can be both frustrating and stressful, finally getting past destroying and getting around to creating is very uplifting.







    And a quick floor plan I did at work whilst trying to look busy.

  • Haven't updated this in a while, but we've been working on it at every opportunity. I think all the hard and dirty work has now been done and we are finally onto more of the good stuff. Making windows and starting on the internal walls this weekend, so it may begin to look liveable soon :). Speaking of walls, does anyone have any cool or alternative ideas, that are pretty rapid to get going? Originally I was going to grab a load of reclaimed planks and such, but it turns out that they are usually way more expensive than buying it brand new, one place was asking within the region of £90 per square meter!!! So now it's good old Wickes and some £7 to £8 per square meter cladding unless inspiration happens.








  • Why not clad with 10mm thick pine tongue and groove. Not too heavy or expensive. Just remember to fit heavier stuff behind for any wall mounted cupboards etc. And it would be pretty easy to calculate how much it would weigh. Or 5.5m ply but that might work out expensive.